Installation guides.

Installation guide

UnderGlow X Pro

Plan the route. Test the lights. Then mount.

1. 01

   Lay out all four strips

   Hold each strip in its planned position without peeling the adhesive backing. This is a dry fit: checking placement before attaching anything.

   Check that every cable reaches its connection without crossing exhaust, wheels, suspension, steering, jacking points, or areas that can scrape.

2. 02

   Connect with power off

   Use the diagram supplied with your exact kit to connect each strip to the controller. Have a qualified automotive installer make the 12V battery connection.

   Keep the diagram with the installer; connector positions and battery connections must follow that kit’s instructions.

3. 03

   Test before sticking

   Power on and confirm that all four strips light. Test the remote or app for your version before attaching the strips.

   If one strip is dark, switch power off, reseat that strip’s connector, and test again before continuing.

4. 04

   Prepare the mounting areas

   Clean each planned mounting area and let it dry completely. Recheck the strip and cable positions before removing the adhesive backing.

   Keep the strips clear of hot and moving parts, jacking points, and scrape areas.

5. 05

   Attach the strips

   Press each strip into place and use the supplied clips where appropriate. Follow the attachment instructions included with your kit.

   Do not cut or extend a strip without instructions specifically for that kit.

6. 06

   Secure the wiring

   Secure the wires separately from the strips. Position and protect the controller, harness, plugs, and any supplied switch as shown in the kit diagram.

   Keep wires clear of heat, moving parts, and pinch points—places where a moving part could trap the cable.

7. 07

   Set up your controls

   Use the control instructions shown below for your selected version. Test the available modes and any cutoff switch supplied with your kit.

   Confirm that you can switch the system off before finishing.

   Use the supplied remote for Solid Colors. This version does not need app pairing.
   Scan the QR code on your Flow Lighting controller or follow the app named in its guide. Use that controller’s pairing instructions.
8. 08

   Make the final check

   Confirm all four strips light, every wire is secured, and nothing can touch a hot or moving part. Switch the system off when parked.

   Check local rules before using exterior lighting on public roads.

Installation guide

AuraSync Ambient Interior Kit

Fit the trim. Keep the wiring out of the way.

1. 01

   Plan each light’s position

   Lay the strips along the intended dashboard and door trim without attaching them. For the 10 Pack, plan the additional footwell lights too.

   Check cable reach and leave enough slack for doors and seats to move normally.

2. 02

   Connect the lights

   With vehicle power off, plug each light into its matching controller port using the guide included with your kit.

   Keep the connections accessible until you have tested every piece.

3. 03

   Run a first light test

   Connect the controller to the USB source supplied or specified for your kit. Turn it on; short-press the controller button if needed.

   Check every piece before tucking strips into trim or pressing adhesive. If a piece is dark, power off and reseat its connector.

4. 04

   Fit the trim strips

   Tuck the flexible strips into suitable trim seams using the supplied attachment method. Where adhesive is used, clean and fully dry the surface first.

   Keep strips away from vents and controls. Never force a strip behind an airbag cover.

5. 05

   Secure the cable routes

   Keep wires clear of pedals, steering, seat tracks, door latches, airbags, and sharp trim. Secure loose cable so it cannot hang into a footwell.

   Keep the slack needed for door and seat movement; do not leave loose loops near the pedals.

6. 06

   Pair the controller

   Scan the QR code on the USB controller for the correct app. Enable Bluetooth and the permissions required by that app, then follow its pairing instructions.

   Test color control in the app and test the supplied remote if your kit includes one.

7. 07

   Check movement before driving

   With the vehicle parked, check that pedals, doors, and seats move normally and that wiring does not interfere with airbags. Confirm all lights still respond.

   Do not cut strips unless the guide for your exact kit gives a marked cut point and cutting method.

Installation guide

CabinGlow Footwell Series

Light the footwells. Leave every control clear.

1. 01

   Choose the light positions

   Choose concealed positions that shine into each footwell. Hold the lights in place before mounting.

   Keep lights clear of the accelerator, brake, clutch, seat tracks, and airbag areas.

2. 02

   Check the cable reach

   Lay out each cable along its planned route. Check that it reaches without rubbing a shoe or crossing a pedal or moving seat.

   Plan enough slack for normal seat movement, with no loose loops in the pedal area.

3. 03

   Connect and test

   With power off, connect the light plugs to the controller following the included diagram. Use only the power source specified for your kit, then turn on.

   Confirm all four lights work before mounting any of them.

4. 04

   Prepare the surfaces

   Clean each mounting surface and let it dry completely. Hold each light in position once more to confirm placement and cable reach.

   Check that the light body will not rub a shoe, pedal, or moving seat.

5. 05

   Mount and secure

   Attach the lights using the supplied mounting method. Secure cables independently of the lights.

   Keep wiring out of airbag zones and away from seat rails and pedals.

6. 06

   Set the lighting

   Use the controls described on your supplied controller or guide. If your kit supports app control, scan that controller’s own QR code.

   Confirm all four lights respond to the controls.

7. 07

   Test seats and pedals

   With the vehicle parked, move the seats through their normal travel and operate the pedals.

   Continue only when the wiring stays secured and every seat and pedal moves freely.

Installer guide

HaloRing Wheel Light Kit

Prepare your kit for a qualified wheel installer.

Professional installation advised. Wheel and brake clearances are safety critical. Use the mounting diagram supplied with your exact kit; check local rules before road use.

1. 01

   Confirm the ring and wheel fit

   Before mounting, have the installer compare each ring with its intended wheel. Check brakes, steering, suspension, tires, and wheel weights.

   The ring must have clearance at the closest point; use the supplied diagram to determine mounting positions.

2. 02

   Test off the vehicle

   Use the battery or power method stated for the kit to test each ring before installation. Use only the app or QR code supplied with its controller.

   Confirm each ring lights and responds to app control before mounting.

3. 03

   Have the rings installed

   The qualified installer should use the supplied mounting hardware and manufacturer’s diagram.

   Never attach to a brake, tire, valve stem, or moving part unless that exact attachment point is specified in the kit instructions.

4. 04

   Check rotation and steering

   Have the installer check full wheel rotation, steering travel, and cable or battery retention. Recheck clearance at the closest point.

   If wheels were removed, they must be refitted using the vehicle maker’s torque procedure.

5. 05

   Retest the lighting

   With the vehicle stationary, test each ring and its controls again.

   If a ring is dark, have the installer inspect its power, controls, and mounting.

6. 06

   Recheck after a short drive

   Have mounting security rechecked after the first short drive and before regular use.

   Stop use if a ring rubs, loosens, or vibrates. Have the installer correct it before using the lights again.

Installation guide

ApexGlow Hood Series

Follow the hood contour. Leave room to move.

1. 01

   Dry-fit the strip

   Hold the strip against the planned hood edge or contour without removing any adhesive backing. Check that the cable reaches its connection.

   Gently open and close the hood to check the strip and cable path around hinges and the latch.

2. 02

   Connect with power off

   Connect the strip and controller as shown in the supplied diagram. Use only the power input specified on the supplied adapter.

   Do not improvise the power connection; use a qualified installer if it is unfamiliar.

3. 03

   Test the colors

   Power on and test color control before mounting the strip. Use the app or QR code identified on the controller or included guide.

   Confirm the strip lights and responds before attaching it.

4. 04

   Prepare the hood edge

   Clean the planned mounting surface and let it dry completely.

   Keep adhesive away from seals, hood-latch engagement surfaces, and drainage paths.

5. 05

   Attach the strip

   Apply the strip using the attachment method supplied with your kit.

   Do not stretch, cut, or crease it unless the included instructions specifically allow that action.

6. 06

   Secure the cable

   Route and secure the cable so it allows normal hood movement. Protect the connectors as directed by the kit instructions.

   Keep it clear of hinges, fans, belts, exhaust, and other hot or moving parts.

7. 07

   Check with the hood open and closed

   Test the colors with the hood open and closed. Confirm the cable does not snag or become trapped as the hood moves.

   Check local rules before using exterior lighting on public roads.

Installation guide

GalaxiFloor Illuminated Mats

A flat fit. A clear pedal area.

1. 01

   Remove the existing mats

   Take out the floor mats already in the vehicle before fitting GalaxiFloor.

   Do not stack another mat above or below a GalaxiFloor mat.

2. 02

   Position each mat

   Lay each mat in its intended floor area, correct side up. Make sure it lies flat.

   On the driver’s side, use the vehicle’s mat retention points if compatible. The mat must stay secure and clear of the pedals.

3. 03

   Connect the lighting leads

   With power off, connect the mat lighting leads as shown in the supplied guide. Use the included USB lead or 12V adapter appropriate to the kit.

   Leave power off while checking and seating connections.

4. 04

   Secure the cables

   Run cables away from the accelerator, brake, clutch, seat tracks, doors, and airbags. Secure loose cable so the mats cannot pull on the leads.

   No cable should cross the driver’s foot controls.

5. 05

   Power on and test

   Power on and check every illuminated area. With the vehicle parked, press each pedal through its full travel and move the seats.

   Remove the driver mat before driving if it cannot be secured or interferes with any pedal.

6. 06

   Recheck after the first drive

   Confirm the mats have not shifted and the cables remain secured.

   Stop using a mat that slides, curls, or limits pedal travel.

Installation guide

StarDome Projector Pro

Plug in. Aim at the ceiling. Check the view.

1. 01

   Choose the USB port

   Use an accessible powered port that does not put the projector in the driver’s knee space or block a control.

   Keep the projector out of pedal and airbag areas.

2. 02

   Plug in the projector

   With the vehicle parked, insert the projector into the compatible USB port.

   Do not force a mismatched connector or use a damaged port.

3. 03

   Aim at the ceiling

   Point the light toward the ceiling and adjust the aim while parked.

   Keep projected light away from the windshield, mirrors, the driver’s eyes, and airbag deployment areas.

4. 04

   Test the starfield

   Turn on USB power and check that the starfield appears. Adjust the aim if needed while the vehicle remains parked.

   Use it only where permitted and where it will not distract the driver.

5. 05

   Check before driving

   Confirm the projector is firmly seated and cannot fall into the pedals.

   Make sure it does not obstruct visibility or any control.

6. 06

   Unplug after use

   Remove the projector when you no longer need it, especially if the USB port stays powered while parked.

   Stop use if the device or port gets hot or looks damaged.